Instructions to Candidates
- This post-test contains 20 multiple-choice questions, each carrying 2 marks (Total: 40 marks).
- Questions are organised according to the first five levels of Bloom's taxonomy: Remember, Understand, Apply, Analyse, and Evaluate.
- Select the ONE most correct answer for each question.
- The recommended time is 40 minutes.
- Post-test answers and explanations are provided at the end of this document for self-assessment.
L1 Remember
L2 Understand
L3 Apply
L4 Analyse
L5 Evaluate
PART A — REMEMBER (Level 1)
Recall fundamental facts, definitions, and classifications of bioelectric signals. (Questions 1–4)
1
Which of the following bioelectric signals is recorded from the heart and represents its electrical activity?
Remember
- EEG (Electroencephalogram)
- ECG (Electrocardiogram)
- EMG (Electromyogram)
- EOG (Electrooculogram)
(2 marks)
2
The resting membrane potential of a typical excitable cell (e.g., a neuron) is approximately:
Remember
- +90 mV
- 0 mV
- −70 mV
- −150 mV
(2 marks)
3
Which pair of ions contributes most directly to the generation and propagation of bioelectric signals across cell membranes?
Remember
- Calcium (Ca²⁺) and Magnesium (Mg²⁺)
- Sodium (Na⁺) and Potassium (K⁺)
- Chloride (Cl⁻) and Bicarbonate (HCO₃⁻)
- Zinc (Zn²⁺) and Copper (Cu²⁺)
(2 marks)
4
In a standard 10–20 electrode placement system, the EEG signal recorded is a measure of electrical activity originating from the:
Remember
- Brain (cerebral cortex)
- Heart muscle
- Skeletal muscle
- Cornea–retina dipole of the eye
(2 marks)
PART B — UNDERSTAND (Level 2)
Explain mechanisms, describe physiological processes, and interpret principles. (Questions 5–8)
5
During an action potential, what causes the rapid depolarisation (rising phase) of the membrane?
Understand
- Efflux of K⁺ through voltage-gated potassium channels
- Influx of Na⁺ through voltage-gated sodium channels
- Efflux of Cl⁻ through ligand-gated chloride channels
- Active pumping of Ca²⁺ into the cell by the Na⁺/K⁺ ATPase
(2 marks)
6
Why must bioelectric signals be amplified before being displayed on a monitor or stored by a data acquisition system?
Understand
- Because the signals are in the millivolt-to-microvolt range — far below the input range of typical ADCs and displays
- Because amplification removes all noise from the signal
- Because the signals are dangerously high in voltage and must be reduced
- Because amplification converts AC signals to DC signals
(2 marks)
7
The P wave on an ECG represents which physiological event?
Understand
- Ventricular repolarisation
- Atrial depolarisation
- Ventricular depolarisation
- Atrial repolarisation hidden behind the QRS complex
(2 marks)
8
Why do bioelectric signals such as the EEG require high common-mode rejection in their amplifiers?
Understand
- Because the body picks up strong common-mode interference (e.g., 50 Hz mains hum) that is much larger than the microvolt-level EEG signal of interest
- Because common-mode rejection increases the signal amplitude tenfold
- Because it converts differential signals into common-mode signals
- Because it eliminates the need for skin preparation at the electrode site
(2 marks)
PART C — APPLY (Level 3)
Use concepts and formulae to solve quantitative and practical problems. (Questions 9–12)
9
A differential biopotential amplifier has a differential gain of 1000 and a common-mode gain of 0.1. A patient recording contains a 5 mV differential ECG signal and a 200 mV 50 Hz common-mode interference. Using CMRR = 20 log₁₀(A_d/A_cm), what is the interference amplitude referred to the output?
Apply
- 20 mV
- 200 mV
- 2 mV
- 20 μV
(2 marks)
10
Using the Nernst equation at 37 °C, E = (61/z) log₁₀([ion]ₒᵤₜ/[ion]ᵢₙ), with intracellular [K⁺] = 100 mM and extracellular [K⁺] = 5 mM, the potassium equilibrium potential is approximately:
Apply
- +77 mV
- −77 mV
- 0 mV
- −122 mV
(2 marks)
11
An EEG technologist observes a rhythmic 10 Hz signal of ~50 μV amplitude over the occipital region when the patient closes their eyes. The most appropriate classification of this activity is:
Apply
- Beta rhythm (alert, eyes open)
- Alpha rhythm (relaxed, eyes closed)
- Delta rhythm (deep sleep)
- Gamma rhythm (>30 Hz)
(2 marks)
12
A surface EMG electrode pair is placed 2 cm apart over the biceps. During contraction, the recorded signal amplitude increases sharply. The most direct physiological explanation for this increase is:
Apply
- More motor units are recruited and their firing rates increase, summing more action potentials at the electrodes
- The skin resistance between the electrodes increases
- The resting membrane potential of all fibres becomes +40 mV
- Action potentials propagate backwards along the muscle fibres
(2 marks)
PART D — ANALYZE (Level 4)
Examine relationships, compare signals, and interpret complex scenarios. (Questions 13–16)
13
A patient recording shows a 50 Hz sinusoidal artefact that is identical in phase and amplitude at both amplifier inputs, while the ECG of interest appears with opposite polarity at the two inputs. Analyzing this situation, the engineer should conclude that:
Analyse
- The artefact is a differential-mode signal and cannot be removed
- The artefact is a common-mode signal and will be strongly attenuated by a high-CMRR differential amplifier, whereas the ECG is a differential signal and will be preserved
- Both signals are common-mode and both will be rejected
- The ECG is common-mode and will be lost during amplification
(2 marks)
14
An ECG trace shows a prolonged QT interval. Analyzing the relationship between the ECG waveform and cellular events, this abnormality most directly indicates delayed:
Analyse
- Atrial depolarisation
- Ventricular depolarisation followed by repolarisation (phase 2–3 of the ventricular action potential)
- Sinoatrial node automaticity
- AV nodal conduction velocity only
(2 marks)
15
Two signals are compared: an ECG (1–5 mV, 0.05–150 Hz) and an EEG (1–100 μV, 0.5–100 Hz). Analyzing these specifications, which design requirement follows for a single front-end amplifier intended for both?
Analyse
- Two completely separate amplifiers are mandatory; no shared design is possible
- The amplifier must provide switchable/programmable gain (to accommodate the ~100× amplitude difference) and an adjustable band-pass covering roughly 0.05–150 Hz
- A fixed gain of 10 with a 1 kHz low-pass filter is sufficient for both
- Only AC coupling at 100 Hz is needed, since amplitude differences are irrelevant
(2 marks)
16
An EOG calibration records a 15 μV signal for a 1° eye movement. During a trial, a recorded deflection of 300 μV is observed. Analyzing the relationship between the cornea–retina dipole and gaze angle, the estimated eye deviation is:
Analyse
- 2°
- 15°
- 20°
- 45°
(2 marks)
PART E — EVALUATE (Level 5)
Make judgments, critique designs, and justify decisions. (Questions 17–20)
17
A biomedical start-up proposes a "one-size-fits-all" amplifier for ECG, EMG, EEG, and EOG with fixed gain of 500, a 50 Hz notch filter, and a single 0.5–40 Hz band-pass. Which evaluation of this design is MOST defensible?
Evaluate
- The design is optimal because it uses the same hardware for all four modalities, reducing cost
- The design will fail: EMG requires bandwidths up to ~1 kHz, ECG needs 0.05–150 Hz, and fixed gain of 500 would saturate with the 5 mV ECG while being marginal for 10 μV EEG — each modality needs tailored gain and filtering
- The design is adequate if the notch filter is removed, since notch filters distort all bioelectric signals
- The design is acceptable because all bioelectric signals have identical amplitude and bandwidth
(2 marks)
18
A clinical engineer must choose between dry electrodes and standard Ag/AgCl gel electrodes for a 24-hour Holter ECG monitor. Which evaluation best captures the key engineering trade-off?
Evaluate
- Dry electrodes are always superior because they eliminate skin preparation and gel application, with no drawbacks
- Dry electrodes offer convenience and long-term stability but typically exhibit higher electrode–skin impedance and more motion artefact; Ag/AgCl gel electrodes provide lower, more stable impedance and better signal quality — the choice depends on whether convenience or signal fidelity dominates the application
- Ag/AgCl electrodes are unusable beyond 1 hour and should never be selected for ambulatory monitoring
- Both electrode types are electrically identical, so the decision is purely cosmetic
(2 marks)
19
A researcher claims that increasing the sampling rate of an EEG acquisition from 250 Hz to 2000 Hz will "improve the accuracy of the 10 Hz alpha rhythm." Which evaluation of this claim is correct?
Evaluate
- The claim is correct; higher sampling always improves accuracy of any signal
- The claim is flawed; by the Nyquist theorem, 250 Hz already exceeds the 20 Hz minimum required to capture a 10 Hz signal faithfully — the extra rate only increases data volume and computational load without improving alpha-rhythm accuracy
- The claim is correct, provided an anti-aliasing filter is removed
- The claim is flawed because EEG signals cannot be sampled digitally at all
(2 marks)
20
An engineering team proposes diagnosing cardiac arrhythmias using a single-lead ECG smartwatch with a claimed accuracy equal to a standard 12-lead clinical ECG. Which evaluation of this proposal is most defensible?
Evaluate
- The claim is fully valid; one lead captures the same spatial information as twelve leads
- The claim is questionable; a single lead views the cardiac dipole from only one direction and can miss arrhythmias localised in planes orthogonal to that lead, whereas 12 leads provide spatial (vectorcardiographic) coverage — wearable single-lead devices are valuable for screening and long-term rhythm surveillance but cannot fully replace clinical 12-lead diagnosis
- The claim is invalid because smartwatches cannot record any ECG signal whatsoever
- The claim is valid if the sampling rate is doubled, since spatial information is equivalent to temporal resolution
(2 marks)
POST-TEST ANSWERS & EXPLANATIONS
Q1 — Answer: B (ECG)
Explanation: The ECG records the heart's electrical activity from the body surface (typical amplitude 1–5 mV). EEG = brain, EMG = skeletal muscle, EOG = eye movements. Recognising these four core modalities is foundational for selecting sensors and amplifiers in biomedical instrumentation. L1 Remember
Q2 — Answer: C (−70 mV)
Explanation: The resting potential of about −70 mV (inside relative to outside) results from the K⁺ concentration gradient and the membrane's selective permeability, maintained by the Na⁺/K⁺ ATPase (3 Na⁺ out, 2 K⁺ in per cycle). This negative resting state is the baseline from which all bioelectric events depolarise. L1 Remember
Q3 — Answer: B (Na⁺ and K⁺)
Explanation: Voltage-gated Na⁺ and K⁺ channels govern the depolarisation and repolarisation phases of the action potential. Their electrochemical gradients (maintained by the Na⁺/K⁺ pump) are the energy source for all bioelectric signals, much like charge stored in a capacitor powering transient currents. L1 Remember
Q4 — Answer: A (Brain / cerebral cortex)
Explanation: The international 10–20 system standardises scalp electrode positions (Fp, F, C, P, O, T regions with 10%/20% spacing) to record cortical activity with amplitudes of 1–100 μV and frequencies from 0.5 to ~100 Hz. Consistent placement allows comparison across clinical and research recordings. L1 Remember
Q5 — Answer: B (Influx of Na⁺ through voltage-gated sodium channels)
Explanation: When threshold (~−55 mV) is reached, voltage-gated Na⁺ channels open rapidly; Na⁺ rushes down its electrochemical gradient, driving the membrane toward +30–40 mV. The subsequent opening of K⁺ channels and Na⁺ channel inactivation produce repolarisation — a classic example of positive feedback followed by negative feedback in a biological system. L2 Understand
Q6 — Answer: A (Signals are mV–μV; below typical ADC/display ranges)
Explanation: Bioelectric amplitudes range from ~1 mV (ECG, EMG) down to ~10 μV (EEG), while typical ADC input ranges are ±1–5 V. Gain stages (differential amplifiers, instrumentation amplifiers) must therefore raise these signals by factors of 10³–10⁴ without adding noise or distortion — the first challenge in any biopotential acquisition chain. L2 Understand
Q7 — Answer: B (Atrial depolarisation)
Explanation: The ECG waveform sequence: P wave = atrial depolarisation; QRS complex = ventricular depolarisation (atrial repolarisation is masked); T wave = ventricular repolarisation. Mapping each waveform to its cellular event is essential for diagnosing conduction disorders. L2 Understand
Q8 — Answer: A (Strong common-mode interference vs. microvolt EEG)
Explanation: Mains interference, electromagnetic coupling, and electrode imbalance all appear identically at both inputs (common-mode), while the EEG appears differentially. Instrumentation amplifiers with CMRR > 100 dB (differential gain 100,000× vs. common-mode gain <1) reject this interference. This is why the electrocardiograph must meet stringent common-mode rejection specifications. L2 Understand
Q9 — Answer: A (20 mV)
Explanation: CMRR = 20 log₁₀(1000/0.1) = 20 log₁₀(10⁴) = 80 dB. Interference at the output = A_cm × V_cm = 0.1 × 200 mV = 20 mV (referred to the input, the effective interference = 200 mV / 10⁴ = 20 μV — compare with the 5 mV ECG). The calculation demonstrates why CMRR directly determines recording quality. L3 Apply
Q10 — Answer: B (−77 mV)
Explanation: E_K = 61 log₁₀(5/100) = 61 × log₁₀(0.05) = 61 × (−1.301) ≈ −77 mV (z = +1 for K⁺). The negative sign arises because K⁺ is more concentrated inside the cell, so the Nernst potential opposes further K⁺ efflux. This computed value closely matches the measured resting potential, validating the Nernst model. L3 Apply
Q11 — Answer: B (Alpha rhythm — relaxed, eyes closed)
Explanation: Alpha activity (8–13 Hz, 20–100 μV, maximal occipitally) appears when the patient is relaxed with eyes closed and attenuates (blocks) upon eye opening or alertness. Beta (>13 Hz, low amplitude, frontal), delta (<4 Hz, deep sleep), and gamma (>30 Hz) do not match the 10 Hz/50 μV occipital profile. L3 Apply
Q12 — Answer: A (More motor units recruited; higher firing rates)
Explanation: Muscle force is graded by two mechanisms: motor-unit recruitment (additional units join) and rate coding (firing frequency rises). Each active unit's action potentials summate at the electrodes, raising the EMG amplitude — the physiological basis for using EMG amplitude as a proxy for muscle force in prosthetics and rehabilitation engineering. L3 Apply
Q13 — Answer: B (Artefact is common-mode; ECG is differential)
Explanation: Identical phase/amplitude at both inputs defines a common-mode signal; opposite polarity defines a differential signal. A high-CMRR amplifier passes the ECG (differential) while attenuating the mains artefact (common-mode). This analysis underpins the differential measurement strategy used in virtually all biopotential instrumentation. L4 Analyse
Q14 — Answer: B (Delayed ventricular depolarisation + repolarisation)
Explanation: The QT interval spans from the start of the QRS to the end of the T wave, encompassing ventricular depolarisation (phase 0–1) and repolarisation (phases 2–3 of the ventricular action potential). Prolongation reflects delayed repolarisation (e.g., long-QT syndrome, drug effects) and increases risk of fatal arrhythmias like torsades de pointes. L4 Analyse
Q15 — Answer: B (Programmable gain + adjustable 0.05–150 Hz band-pass)
Explanation: The ~100× amplitude difference demands switchable gain (e.g., ×1000 for EEG, ×100 for ECG); the union of bandwidths (0.05–150 Hz) must be covered without attenuating diagnostically relevant content. Designing for the union of specifications is a standard systems-engineering approach to multimodal acquisition front-ends. L4 Analyse
Q16 — Answer: C (20°)
Explanation: The EOG reflects the orientation of the cornea(+)–retina(−) dipole: 300 μV ÷ 15 μV/° = 20°. The linearity of the EOG with gaze angle holds for roughly ±30°, after which the dipole geometry becomes non-linear. This calibration relationship is exploited in eye-tracking and sleep-monitoring systems. L4 Analyse
Q17 — Answer: B (Design will fail — EMG needs ~1 kHz, fixed gain mismatched)
Explanation: Typical specifications: EEG 0.5–100 Hz (μV), ECG 0.05–150 Hz (mV), EMG 20 Hz–1 kHz (mV), EOG 0.1–10 Hz (μV). A 40 Hz low-pass would destroy the EMG; fixed gain of 500 saturates on 5 mV ECG (2.5 V output clipping) yet is marginal for 10 μV EEG. The evaluation demonstrates that modal-specific tailoring is an engineering necessity, not an option. L5 Evaluate
Q18 — Answer: B (Trade-off: dry = convenient but higher impedance/motion artefact; gel = better signal)
Explanation: Ag/AgCl gel electrodes achieve stable, low skin–electrode impedance (~5–10 kΩ) and low motion artefact, but gel dries out and irritates skin over long recordings. Dry electrodes avoid these issues but exhibit higher, less stable impedance and greater susceptibility to motion artefact. For 24-hour ambulatory Holter monitoring, this trade-off between patient comfort/convenience and signal fidelity must be weighed explicitly. L5 Evaluate
Q19 — Answer: B (Claim flawed — Nyquist: 250 Hz already exceeds the 20 Hz minimum)
Explanation: Nyquist requires f_s > 2f_max = 20 Hz for a 10 Hz signal; sampling at 250 Hz already provides 25× oversampling, so no accuracy improvement results from 2000 Hz. Higher rates inflate storage (8× data), computational burden, and power consumption — critical constraints in portable biomedical devices. Good engineering evaluates necessity before adding capability. L5 Evaluate
Q20 — Answer: B (Claim questionable — single lead lacks spatial coverage of 12 leads)
Explanation: A 12-lead ECG views the cardiac electrical vector from 12 spatial orientations (limb leads via Einthoven's triangle + precordial leads), enabling localisation of ischaemia and conduction defects. A single-lead wearable (e.g., Lead I from a smartwatch) is excellent for rhythm screening (AFib detection) and long-term surveillance but cannot replace the diagnostic spatial resolution of 12 leads. The evaluation weighs genuine clinical utility against marketing overreach. L5 Evaluate